OutBack DC Breaker 20 amp 125 VDC with 1/4" stud terminals.

Requires one small 3/4" breaker space.

AIC Rating: 7.5K at 80 VDC

DC breaker - 250 amp 125 VDC large size – 1.5” wide

OutBack DC Breaker 40 amp 125 VDC with 1/4" stud terminals.

Requires one small 3/4" breaker space.

AIC Rating: 7.5K at 80 VDC

DC breaker - 70 amp 125 VDC small size – 0.75” wide

The OutBack Power Systems FLEXnet™ DC is the ultimate in DC System monitoring devices.

The integrated networked communications make valuable, usable data available from your system, viewable on an OutBack MATE communications device, providing you with the answers you need concerning your system’s health, performance and efficiency.

Outback FX-ACA AC wiring compartment extension and 2" conduit adapter.

Required when mounting an FX inverter/charger to an OutBack PS2AC or PS4AC.

Includes two 1" conduit knockouts and an AC outlet knockout.

The Outback FX-DCA DC Conduit Adapter allows connection of 2” DC conduit or enclosure to a FX or VFX inverter.

The OutBack HUB-10 system communications manager allows the interconnection of up to ten OutBack power conversion devices with the MATE. The interconnection creates a completely integrated Power System that is coordinated and managed by the MATE.

The OutBack HUB-10 communicates stacking phase, load share, incremental start-up and shut-down information directly between the inverters. Interconnection cabling is standard ethernet CAT5 eight wire with RJ45 modular jacks. The HUB-10 is ...

The OutBack HUB-4 system communications manager allows the interconnection of up to four power conversion devices with the MATE. The interconnection creates a completely integrated Power System that is coordinated and managed by the MATE.

The OutBack HUB-4 communicates stacking phase, load share, incremental start-up and shut-down information directly between the inverters. Interconnection cabling is standard ethernet CAT5 eight wire with RJ45 modular jacks. The HUB is powered via ...

OutBack Mate for one or more FX, VFX and/or MX60. Four line 80 character LCD display with backlight. RS232 port for PC connection (software not included). Wall surface mount with 3' and 50' catV cable included.

Highly recommended for any OutBack inverter system for setpoint adjustment and monitoring. Plugs into the Stack-2 or Stack-4 or Hub-4 or Hub-10 for stacked inverters.

We recommend the Hub over the Stack so all inverters can be monitored without unplugging cables (the ...

OutBack Mate for one or more FX, VFX and/or MX60. Four line 80 character LCD display with backlight. RS232 port for PC connection (software not included). Wall surface mount with 3' and 50' catV cable included.

Highly recommended for any OutBack inverter system for setpoint adjustment and monitoring. Plugs into the Stack-2 or Stack-4 or Hub-4 or Hub-10 for stacked inverters.

We recommend the Hub over the Stack so all inverters can be monitored without unplugging cables (the ...

Power System AC Disconnect breaker assembly with quad 60A-AC IOB assembly (for 4 Outback inverters). Already installed in PSAC enclosure and ready to go (inverters not included).

Outback quad stack DC disconnect box. Already prewired and ready to go (inverter are not included).

Mounting Plate - 36"x50" steel backplane for mounting SW, PS, DR, etc inverters. Already prewired for an Outback quad stack and ready to go (inverters not included).

Remote Temperature Sensor for FX, VFX or MX60 products

Terminal Bus Bar kit with black plastic insulators – use as L1 hot or DC negative.

Terminal Bus Bar kit with red plastic insulators – use as L2 hot or DC positive.

DC Ground Fault Protection / Dual Circuit – uses three of the small breaker spaces